Kti-networks KF223TX Manuel d'utilisateur

Installation Guide10/100 Dual-speedFast Ethernet PCI AdaptersDOC.971115-KF223/230TX-KP/N:750-0099-001KF223TX, KF230TX

10 Mbps ConnectionFor 10BASE-T Ethernet networks, the Fast Ethernet adapter usesCategory 3, 4, or 5 UTP cable. To establish a valid 10 Mbps connec-tio

100 Mbps ConnectionFor 100BASE-TX Fast Ethernet networks, the adapter supports Cat-egory 5 UTP cabling. To establish a valid 100 Mbps connection, thec

3. Network Driver InstallationAfter making the connection to the network, you must install theadapter network driver in order to connect the Fast Ethe

may be included in the driver diskette after this guide is published.Please refer to the \README.DOC file first for the latest informa-tion before you

4. Setup Program4.1 Running Setup ProgramOne setup program, SETUP.EXE, is contained in the adapter driverdiskette. The Setup program is a DOS program

You can run the program and perform the tests at any time afterinstalling the adapter to verify the installation or you can run it when afault is susp

Starting the Setup ProgramTo start the Setup program, follow these steps:1. Insert the adapter driver diskette labeled "1 of 2" into floppy

4.2 Functions on the Main MenuThis section describes the functions of "Install", "Setup", and "Diag-nostics" menu on the

Running "Setup" MenuThis menu allows you to configure full-duplex mode forthe adapter before running Connectivity test.Figure 4-4 Setup Menu

Running "Diagnostics" MenuThis menu provides two useful functions: Diagnostics and Connectiv-ity test.Figure 4-5 Diagnostics MenuDiagnostics

Ó 1997, KTI Networks Inc. All rights reserved. No part of this docu-mentation may be reproduced in any form or by any means or used tomake any directi

To set up an echo station, follow these steps:1. Install another adapter which is known to have no problem into asecond computer as instructed in Chap

4. Select "Connectivity Test" and press [Enter].5. Make sure an echo station is ready. Select "Start Network LinkTest" from "

5. LED IndicatorsEach Fast Ethernet adapter has three LEDs, as shown in Figure 1-1.5.1 InterpretationsThe interpretations of the LEDs are:100Mb LED in

AppendixA1. SpecificationsNetwork std.: 10 Mbps IEEE 802.3 10BASE-T Ethernet100 Mbps IEEE 802.3u 100BASE-TX Fast EthernetDimensions: MX98713 NIC 80mm

A2. RJ-45 Connector & CablesFigure A-1 shows the pin assignments of the RJ-45 connector for10BASE-T and 100BASE-TX network. The pin assignments ar

A.3 Auto-negotiation FunctionThe adapter is equipped with an auto-negotiation function. Auto-ne-gotiation is a negotiation procedure between two conne

A.4 Diagnostics ReportWhen running "Diagnostics" from the SETUP program, the programindicates the result of each test on the Diagnostics Rep

A.5 Installing Remote Boot ROMBefore you can use the remote boot function, you have to setup theremote boot service on the file server and install the

TRADEMARKSEthernet is a registered trademark of Xerox Corp. NetWare is a registered trademarkof Novell Inc.WARNING:This equipment has been tested and

10/100BASE-TXFAST ETHERNET PCI ADAPTERSINSTALLATION GUIDEDOC.971114DF223TX-KF230TX-NKP/N:750-0099-002

Table of Contents1. Introduction1.1 Adapter Features ... 11.2 Connector and LEDs ...

1. IntroductionThe 10/100BASE-TX Fast Ethernet PCI Adapter is a 32-bit LANadapter for use in personal computers with PCI computer bus slots.This adapt

1.2 Connector and LEDsFigure 1-1 shows the connector and LEDs on the adapter. The fol-lowing table describes these components.No. Components Descripti

2. Installing the AdapterThis chapter describes how to install the Fast Ethernet PCI adapterin a PCI computer and how to connect the adapter to the ne

Figure 2-1 Inserting the Adapter into the PCI Slot2.2 Connecting to the NetworkThis section describes how to connect 10 Mbps or 100 Mbps net-work cabl