Kti-networks Web Smart Managed 10/100 Fast Ethernet Switches wi Manuel d'utilisateur

-1-Installation GuideWeb Smart Managed10/100 Fast Ethernet Switcheswith VLAN SupportKS-115FM-VKS-117FM-VDOC.030430-KS115FM-V-KS117FM-V-K

-10-2. Installing the Switches2.1 UnpackingCheck to see that you have everything before you start the installation.• Installation guide• The switch un

-11-2. Connect the power adapter cable to the switch before connectingthe adapter to the AC outlet.2.3 Port ConfigurationThe switches provide port con

-12-2.4 VLAN FunctionThe switches support two VLAN modes. One is Port-based VLAN andthe other is 802.1Q VLAN.The following configuration are supported

-13-802.1Q VLAN Mode1. This mode supports 16 VLAN groups, Group 0 ~ Group 15.2. When an untagged packet is received, the associated PVID settingof the

-14-Summary of VLAN Group Lookup (Group Mapping Index)Input Packet Type Port-based VLAN Mode 802.1Q VLAN ModeUntagged packet PVID bit3-0 of input port

-15-2.5 DHCP and IP ConfigurationEach switch must be designated an IP address before it can be managedfrom web browser. Basically, the switches provid

-16-2.7 Making UTP ConnectionsTP Port ConfigurationUse management function to set the required TP port configuration. It isrecommended to set the high

-17-2.8 Making Fiber ConnectionFor different fiber connections, several alternative models can beselected for different fiber connections as follows:M

-18-2.9 LED IndicationsFunctionsPOWER : indicates the status of the power supplied to the switch.100/10 : indicates the connection speed between the T

-19-3. Web Management3.1 Web BrowserThe system features an http server which can serve the managementrequests coming from any web browser software ove

-2-(C) 2002 KTI Networks Inc. All rights reserved. No part of this documen-tation may be reproduced in any form or by any means or used to makeany dir

-20-Enter your password and click [OK] to login into the switch. The switchcomes with factory default password : 123.

-21-The web page is shown as follows when a successful login is performed:The left side shows the switch model and menu list. The list includes :[Port

-22-3.2 Port SetupThe middle part of previous figure shows all port status of the connectedswitch. The right side shows port configuration setup page.

-23-3.3 IP SetupThis page includes the following functions:IP Status Display information of current IP usedIf the current IP address is labeled (DHCP)

-24-3.4 VLAN SetupVLAN Mode SelectPort-based VLAN : Port-based VLAN802.1Q base VLAN : IEEE 802.1Q Tag-based VLANClick [Apply] to make change effective

-25-3.4.1 Port-based VLANClick [VLAN Mapping Table]This page is used to setup member ports for each VLAN group. Total of16 VLAN groups are supported.T

-26-Click [Port PVID Setting]This page is used to setup PVID and Tag mode for each port as follows:PVID : The setting value is used for VLAN group loo

-27-3.4.2 802.1Q VLANClick [VLAN Mapping Table]This page is used to setup member ports for each VLAN group. Total of16 VLAN groups are supported. Actu

-28-Click [Port PVID Setting]This page is used to setup PVID and Tag mode for each port as follows:PVID : The valid value range is 1 ~ 4095. The setti

-29-Tag Mode : Setting for each port to be Tag port or Untag port for out-bound.Tag port - All output packets are tagged.Untag port - All output packe

-3-The information contained in this document is subject to change without prior notice.Copyright (C) All Rights Reserved.TRADEMARKSEthernet is a regi

-30-.5 Password SetupPassword is used for checking authority for accessing the switch. Tochange password setting, enter your new password and reconfir

-31-3.6 Restore DefaultThis command is used to restore all settings back to factory defaultvalues. Click [Restore] to apply immediately. Refer to Appe

-32-3.7 ReBoot DeviceThe command is used to reboot the switch remotely over the network.Normally, it is used after IP settings are changed.

-33-3.8 AboutAbout page shows switch model name and software version.

-34-Appendix: Factory Default ValuesSettings Factory Default ValuesDHCP mode EnabledStatic IP address 192.168.0.2Netmask 255.255.255.0Default gateway

-4-Table of Contents1. Introduction ...51.1 Features ...

-5-1. IntroductionThis guide describes the specifications and installation instructions forthe following two managed 10/100 switch series:KS-115FM-V s

-6-1.1 Features• The 10/100BASE-TX switched ports support:- Auto speed sensing for 100Mbps or 10Mbps connection- Auto configuration for connected auto

-7-1.2 SpecificationsFigure : Major Components on Panels (Ex. KS-117FM-V)KS-115FM P1-P4 Port 1 ~ Port 4 Twisted-pair switched ports (TP ports)KS-117FM

-8-Filtering address Multicast/Broadcast/Unicast addressMAC address 2K entriesAging time 300 secondsPriority levels 2 outgoing priority queues (Ratio:

-9-1.4 Management SpecificationsInterface In-band web browser for IE4.0 and Netscape4.xPing command, ARP commandProtocols IPv4, ARP, ICMP,UDP, TCP, DH